FESTO 8061199 Actuador integrado

EMCA-EC-67-S-1TM-DIO

$1.824,05
Stock Limitado solo disponible bajo consulta

Especificaciones

Serie (EMCA) Motor with controller
Motor type (EC) EC motor
Flange size, motors (67) 67
Length (S) Short
Nominal operating voltage (1) 24 V DC
Conexión eléctrica (T) Terminal box
Measuring unit (M) Absolute encoder, multi-turn
Brake None
Bus protocol/activation (DIO) Digital I/O interface
Degree of protection, electrical system Standard
Nota sobre el material Contains paint-wetting impairment substances RoHS-compliant
Switching logic for outputs PNP (positive switching)
Ethernet, supported protocols TCP/IP, Modbus TCP
Working range of logic input 24 V
Communication profile FHPP
Number of digital logic outputs 24 V DC 4
Proof test interval 20 y
Permissible axial shaft load 60 N
Par de apriete nominal 0,37 Nm
Note on ambient temperature Power must be reduced by 1.75% per °C at ambient temperatures above 20°C.
Grado de protección IP54
Temperatura de almacenamiento -25 °C ... 70 °C
Resistencia a las vibraciones Transport application test with severity level 2 to FN 942017-4 and EN 60068-2-6
Organismo que expide el certificado TÜV 01/205/5514.00/16 UL E331130
Certificación RCM trademark c UL us - Recognized (OL)
Peak current 10,2 A
Rotor position transducer resolution 12 bit
Operating time absolute encoder With external battery: up to 6 months Note: the maximum service life of the battery depends on its charging status, the ambient temperature and ageing effects. Without external battery: 3 days (worst case) up to max. 7 days (best case) Note: The maximum storage time depends on the charge state of the internal capacitor, ambient temperature and ageing effects.
Protocolo Modbus® TCP
Nominal current 6,9 A
Nominal power rating of motor 120 W
Max. positive test pulse with 0 signal 10.000 µs
Hardware fault tolerance 1
Diagnostic coverage 90 %
Nominal rotary speed 3.100 rpm
Indicación LED
Safety Integrity Level (SIL) Safe torque off (STO)/SIL 2
Protective function I²t monitoring Temperature monitoring Current monitoring Voltage failure detection Following error monitoring Software end-position detection
Rotor position sensor Absolute multi-turn encoder
Tipo de fijación Screw-clamped With through-hole
Switching logic for inputs PNP (positive switching)
Features of logic input Galvanically connected to logic potential
Specification logic input Based on IEC 61131-2
Number of digital logic inputs 11
Peso del producto 1.925 g
Permissible radial shaft load 100 N
Peak torque 0,85 Nm
Mass moment of inertia of rotor 0,175 kgcm²
Temperatura ambiente 0 °C ... 50 °C
Humedad relativa del aire 0 - 95% Non-condensing
Resistencia a los golpes Shock test with severity level 2 to FN 942017-5 and EN 60068-2-27
Marcado CE (véase la declaración de conformidad) To EU EMC Directive To EC Machinery Directive
Símbolo KC KC-EMV
Fluctuaciones de tensión admisibles +/- 20 %
Max. output motor 158 W
Max. number of process sets 64
SFF Safe Failure Fraction > 90 %
Parameterisation interface Ethernet
Nominal voltage DC 24 V
Max. negative test pulse with 1 signal 600 µs
Max. current digital logic outputs 100 mA
Features of digital logic outputs Freely configurable in some cases Not galvanically isolated
Brake resistor, external 6 Ohm
Revoluciones máx. 3.500 rpm
Performance Level (PL) Safe Torque Off (STO)/category 3, performance level d
Función de seguridad Safe torque off (STO)
Rotor position sensor, encoder measuring principle Magnetic
Controller operating mode PWM MOSFET power output stage Cascade controller with P position controller PI speed controller PI current regulator
$1.824,05
Stock Pedir cotización
Referencia 8061199
Fabricante FESTO
Unidades Precio / Unidad
1+ $1.824,05

  • Registro abierto
    Crea una cuenta en el momento
  • Soporte 24/7
    Pregúntanos a cualquier hora
  • 100% Seguro
    Solo pagos seguros: transferencia bancaria, tarjeta de cédito y PayPal
  • Descuentos por volumen
    Optimice sus suministros